home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
Libris Britannia 4
/
science library(b).zip
/
science library(b)
/
HAM_RAD
/
LOGGING
/
2373.ZIP
/
LOGEQF.EXE
/
LOG-EQF.DOC
< prev
next >
Wrap
Text File
|
1994-01-18
|
138KB
|
2,466 lines
PAGE i
Log-EQF is distributed as Shareware.
Continued use of this program requires that you become a Registered User.
See page v of this manual for registration details.
------------
USER'S GUIDE
------------
╔═══════════════════════════════════╗
║ ║
║ ╦ ╔═╗ ╔══ ╔══ ╔═╗ ╔══ ║
║ ║ ║ ║ ║ ══ ╠═ ║ ║ ╠═ ║
║ ║ ║ ║ ║ ╦ ║ ║ ║ ║ ║
║ ╩══ ╚═╝ ╚═╝ ╚══ ╚═╠ ╩ ║
║ Version 5.27 ╨ ║
║ Copyright (C) 1989 - 1993 ║
║ Thomas Dandrea - N3EQF ║
║ ║
║ -ALL RIGHTS RESERVED- ║
║ ║
╚═══════════════════════════════════╝
Tom Dandrea, N3EQF
396 Sautter Drive
Coraopolis, PA 15108-9244
USA
- EQF Software -
(412) 457-2584
_______
____|__ | (R)
--| | |-------------------
| ____|__ | Association of
| | |_| Shareware
|__| o | Professionals
-----| | |---------------------
|___|___| MEMBER
Throughout this manual any commercial trade names mentioned are
either trademarks or registered trademarks of their developers.
Use of these trade names does not indicate an endorsement by the
trademark owners.
--------------------------------CONTENTS----------------------- PAGE ii
Definition of Shareware & Disclaimer...................iv
Registration and Support & Ombudsman....................v
1. Log-EQF Overview......................................1.0
2. Installation..........................................2.0
SYSTEM REQUIREMENTS........................2.0
INSTALLING Log-EQF.........................2.0
FILES REQUIRED FOR OPERATION...............2.1
3. Program Startup and Customization.....................3.0
CONFIGURATION SETUP........................3.0
LOADING LOGBOOK INFORMATION FROM FILES.....3.3
QUICK STARTUP OF Log-EQF...................3.5
USING THE CALLSIGN DATABASE INTERFACES.....3.6
4. Main Menu Commands....................................4.0
VIEW IN DETAIL.............................4.1
QUICK VIEW.................................4.2
PRINT LOGBOOK..............................4.3
QSL LABELS.................................4.4
LOG - AUTOMATIC............................4.5
LOG - MANUAL...............................4.9
EDIT.......................................4.11
LOAD.......................................4.13
SORT.......................................4.14
SEARCH.....................................4.16
NORMAL/CONTEST SELECTION...................4.17
RUN ANOTHER PROGRAM........................4.18
SETUP......................................4.19
EXIT.......................................4.19
5. Contest Operation.....................................5.0
INTRODUCTION...............................5.0
CONFIGURATION SETUP........................5.1
OPERATION DURING THE CONTEST...............5.4
OPERATION AFTER THE CONTEST................5.6
6. Radio Interface Operation.............................6.0
7. Terminal Node Controller (TNC) Operation..............7.0
8. Maintenance of the DX Prefix Library..................8.0
9. In Case of Trouble....................................9.0
PAGE iii
[This page intentionally left blank]
DEFINITION OF SHAREWARE PAGE iv
-----------------------
Shareware distribution gives users a chance to try software before buying
it. If you try a Shareware program and continue using it, you are expected
to register. Individual programs differ on details -- some request
registration while others require it, some specify a maximum trial period.
With registration, you get anything from the simple right to continue
using the software to an updated program with printed manual.
Copyright laws apply to both Shareware and commercial software, and the
copyright holder retains all rights, with a few specific exceptions as
stated below. The main difference is in the method of distribution. The
author specifically grants the right to copy and distribute the software,
either to all and sundry or to a specific group.
Shareware is a distribution method, not a type of software. You should
find software that suits your needs and pocketbook, whether it's
commercial or Shareware. The Shareware system makes fitting your needs
easier, because you can try before you buy. And because the overhead is
low, prices are low also. Shareware has the ultimate money-back guarantee
-- if you don't use the product, you don't pay for it.
DISCLAIMER - AGREEMENT
----------------------
Users of Log-EQF must accept this disclaimer of warranty: "Log-EQF is
supplied as is. The author disclaims all warranties, expressed or
implied, including, without limitation, the warranties of merchantability
and of fitness for any purpose. The author assumes no liability for
damages, direct or consequential, which may result from the use of
Log-EQF." Log-EQF is a "shareware program" and is provided at no charge
to the user for evaluation. Feel free to share it with your friends, but
please do not give it away altered or as part of another system. The
essence of "user-supported" software is to provide personal computer users
with quality software without high prices, and yet to provide incentive
for programmers to continue to develop new products. If you find this
program useful and find that you are using Log-EQF and continue to use
Log-EQF after a reasonable trial period, you must make a registration
payment of $25 to N3EQF. The $25 registration fee will license one copy
for use on any one computer at any one time.
Anyone distributing Log-EQF for any kind of remuneration must first
contact N3EQF at the address above for authorization. This authorization
will be automatically granted to distributors recognized by the (ASP) as
adhering to its guidelines for shareware distributors, and such
distributors may begin offering Log-EQF immediately (However N3EQF must
still be advised so that the distributor can be kept up-to-date with the
latest version of Log-EQF).
You are encouraged to pass a copy of Log-EQF along to your friends for
evaluation. Please encourage them to register their copy if they find
that they can use it. All registered users will receive a copy of the
latest version of the Log-EQF system.
REGISTRATION AND SUPPORT POLICY PAGE v
-------------------------------
To become a registered user of Log-EQF, you must send a $25 fee to the
author at the address below:
┌───────────────────────────────┐
│ Tom Dandrea, N3EQF │
│ 396 Sautter Drive │
│ Coraopolis, PA 15108-9244 │
│ │
│ Phone: (412) 457-2584 │
└───────────────────────────────┘
To register, use the form shown on the following page, or provide the
information below in any readable format to N3EQF:
- Current version number of Log-EQF you're using.
- The type of floppy disk you require (i.e., 360K)
- Your amateur callsign.
- Complete mailing address.
When you become a registered user, you are provided the following:
1. The current version of Log-EQF will be sent upon receipt of payment.
The program will be supplied on the floppy type you specify.
2. In addition to the Log-EQF program, you will be provided with two
utility programs for importing logbook files from other logging
programs into Log-EQF, and for tracking DXCC award progress.
3. You will be automatically notified when major revisions to Log-EQF
are released.
4. Technical support is available at the above address and phone number,
for a minimum period of 6 months after the registration date. N3EQF
makes every attempt to correct any problems reported about the use of
the Log-EQF program. I also welcome constructive criticism and
suggestions for improvement. The current version of Log-EQF rep-
resents the collective input received from registered users over more
than four years.
OMBUDSMAN
---------
Tom Dandrea, N3EQF, is a member of the Association of Shareware
Professionals (ASP). ASP wants to make sure that the shareware principle
works for you. If you are unable to resolve a shareware-related problem
with an ASP member by contracting the member directly, ASP may be able to
help. The ASP Ombudsman can help you resolve a dispute or problem with an
ASP member, but does not provide technical support for members' products.
Please write to the ASP Ombudsman at 545 Grover Road, Muskegon, MI 49442
or send a CompuServe message via CompuServe Mail to ASP Ombudsman
70007,3536.
REGISTRATION FORM PAGE vi
Log-EQF 5.27 Registration and Order Form
Your Name: _______________________________Callsign:_____________
Address: _______________________________________________________
City: _____________________________ State/Province: ____________
Country: ____________________________ Zip/Postcode: ____________
-----------------------------------------------------------------
Log-EQF Registration ...............................: $25.00
* For orders outside of the U.S., Canada, and Mexico, please
add $3.00 shipping and handling.
Please indicate the disk size you prefer: .... __5 1/4" __3 1/2"
Payment must be in U.S. funds, drawn on a U.S. bank. Pennsylvania
residents please add 6% sales tax. Please send the completed form,
along with a check or money order to:
EQF Software Technical Support: (412) 457-2584
Tom Dandrea, N3EQF
396 Sautter Drive (Evenings & weekends, or
Coraopolis, PA 15108 U.S.A. leave a message on machine).
-------------------------------------------------------------------
You can also order with your Master Card or Visa from WestWorld
Computer Services:
By mail: By Email:
-------- ---------
WestWorld Computer Services Genie: WESTWORLD
3755 Avocado Blvd Suite 304 CompuServe: 70574,450
La Mesa, CA 91941-7301 America On-line: WESTWORLD
Prodigy: JSPB88A
Delphi: WESTWORLD1
By calling: 800-995-1605 (24 hours)
-----------
From overseas: 619-685-7291 (24 hours)
--------------
FAX to: 619-558-7850.
-------
THESE NUMBERS ARE FOR ORDERING ONLY.
EQF Software can NOT be reached at those numbers. To contact N3EQF
for information about anything other than to place a credit card
order or to receive authorization for returns, call Tom Dandrea at
412-457-2584, or write N3EQF at 396 Sautter Drive, Coraopolis, PA.
OVERVIEW PAGE 1.0
1. LOG-EQF OVERVIEW
--------------------
The Log-EQF program helps you maintain a complete and accurate station
logbook with minimal effort. Log-EQF will function as a full-featured
electronic logbook when used alone on a personal computer. If the pro-
gram is used on a computer that is connected to a transceiver interfaced
via an RS-232C serial port, many additional automatic logging and con-
trol features are enabled. Your TNC is also supported by Log-EQF, with
PacketCluster (tm), file upload and download, and a monitor window on the
logging screen.
Below are some of the features of Log-EQF:
- DAILY LOGBOOK (STAND-ALONE)
---------------------------
- Easy to use menus for all operations, complete with mouse control.
- Full-screen entry of logbook information in any order desired.
- Easy edit or deletion of any logbook entry.
- Automatic date and time logging with built-in UTC conversion.
- Quick reports of DXCC Zone and Continent info from callsign prefix.
- Beam Headings displayed from DXCC prefix of callsign.
- Abbreviated or complete display of logbook entries.
- Ability to search logbook for a pattern in any entry field.
- Able to sort logbook files by any field.
- Print all or part of logbook, either in abbreviated or detailed form.
- Print QSL labels with personalized message line.
- Customized screen colors and on-screen display of your callsign.
- Run other programs while Log-EQF stays in memory (EMS if installed).
- Monitor PACKET or any other TNC operation while logging.
- Interfaces with SAM database system for automatic name and QTH entry.
- 10-minute identification reminder.
- CONTEST MODE
------------
- Fast dupe checking with displayed details.
- Optional automatic generation of serial numbers for exchange.
- Optional printout of each entry as it's logged (data security).
- Generate Dupe sheets.
- Print entry logbook w/ auto QSO and multiplier totals (user-defined).
- ASCII disk files created for dupe sheets and contest logs.
- Partial callsign check.
- On-screen QSO rate and lapse time displays.
- RADIO INTERFACE
---------------
- Automatic display and logging of radio mode and frequency.
- Control over radio VFO and mode from log entry screens.
- "Hot key" access to the optional Rig-EQF Kenwood rig control program.
- On-screen display of two VFOs and "TRANSMIT" for Kenwood radios.
- On-screen display for last station heard on what frequency.
INSTALLATION PAGE 2.0
2. INSTALLATION
----------------
- SYSTEM REQUIREMENTS
-------------------
- IBM PC, XT, AT, PS/2 or compatible.
- DOS 3.0 or higher.
- 512K memory (The program executable requires about 200K).
- Monochrome or color monitor (no graphics adapter required).
- 1 floppy drive and/or a hard drive (hard disk drive recommended).
- (optional) 1 serial comm port (COM1-COM4) for radio interface.
- (optional) 1 serial comm port for Terminal Node Controller (TNC).
- 1 parallel printer port and printer recommended.
- Mouse (Microsoft compatible), bus mouse if all COM ports are used.
If a radio is to be interfaced to your computer for use with Log-EQF, it
must be connected to the computer's serial port following the radio
manufacturer's documentation guidelines. For many radios, a TTL/RS232C
converter must be used between the computer and radio. See Chapter 6 of
this manual for more information about radio computer interfacing.
You may also use a Terminal Node Controller (TNC) with Log-EQF. Log-EQF
is compatible with any TNC designed to work with standard TTY or ANSI
terminal emulation communication software. No attempt is made to control
a TNC in host mode.
- INSTALLING LOG-EQF SOFTWARE
---------------------------
Before proceeding, make a WORKING copy of the Log-EQF floppy. (Refer to
your DOS manual for information about copying programs). USE THE
WORKING COPY YOU CREATE TO INSTALL LOG-EQF, AND MAINTAIN YOUR ORIGINAL
DISK IN A SAFE PLACE!
Log-EQF comes in compressed format, so that all the reqired files will fit
onto a single 360K floppy. A file called INSTALL will unpack all the
necessary files onto the disk or directory you specify. If you did not
receive an INSTALL program, the files for Log-EQF can be installed by
typing:
LOGEQF C:\LOG-EQF\
...where "C:\LOG-EQF\" is the disk drive and directory where you Log-EQF
to be located. Note that the directory (usually called LOG-EQF) must be
created using DOS before installing Log-EQF in this manner.
NOTE: After installing Log-EQF, check your CONFIG.SYS file in the root
dirctory for a statement that says: FILES = 20 (or higher than 20).
This prevents an error from occuring in Log-EQF, when multiple files are
open at the same time. Consult your DOS manual for further information.
INSTALLATION PAGE 2.1
- FILES REQUIRED BY LOG-EQF
-------------------------
The following is a list of files which are necessary for all functions
of Log-EQF to operate, along with their description:
* LOG-EQF.EXE Main executable logbook module
* LOG-EQF.CNF User-defined configuration parameters (created the
first time LOG-EQF is run).
DUPE-EQF.EXE Dupe-sheet and contest log generation module
* PREFIX.LIB DXCC Prefix Library (Also used for beam headings)
* STATES.LIB Beam Heading file for STATE field.
LOG-EQF.DOC Documentation File (User's Guide) for Log-EQF
5.KEY-10.KEY Macro files (OPTIONAL) for use with TNC function keys
SHELL1?.BAT BATCH files to be executed by the <F11> and <F12> keys
????????.RIG Radio configuration files (OPTIONAL) for interfacing
If disk space is limited, and you do not require contest operation or
the DXCC or file-conversion utilities, you can install only those files
marked with an asterisk (*) on your disk. DUPE-EQF.EXE can also be omitted
if you will not be working contests with Log-EQF.
Logbook file names are defined by the user. The only limitation on file-
names are the restrictions imposed by DOS; file names can be no longer
than 8 characters. Log-EQF automatically adds the ".LOG" file extension
to the end of the logbook name you define. When you enter a logbook name
from within Log-EQF, you do not type the ".LOG" extension. To load the
sample logbook, for example, you type in only "SAMPLE".
Besides the ".LOG" logbook files, Log-EQF also creates a notepad file
using the same name as your logbook, but with ".NOT" as the file
extension. The notepad file contains 480 characters of text for any QSO
which you decide to write a notepad.
CONFIGURATION PAGE 3.0
3. PROGRAM STARTUP AND CUSTOMIZATION
-------------------------------------
- CONFIGURATION SETUP
-------------------
The first time you run Log-EQF, you will be directed automatically to
the Log-EQF configuration setup menu. If you wish to change a previously-
defined configuration, you can access the setup menu by selecting it from
the Log-EQF Main menu.
-------------------------------------------------------------------------
Log-EQF Copyright (C) 1993, N3EQF SETUP MENU - Hit <Esc> to exit
-------------------------------------------------------------------------
Callsign ->N3EQF
Latitude (N = +)? 40.5 [Degrees as a decimal number]
Longitude (E = +)? -80.1
Hours to add to clock time for UTC ->5 [Enter 0 if computer = UTC]
POWER level used most often ->100
Logbook Name used most often ->LOGBOOK
First Program Name for SHELL->DX-EQF %C
Second Program Name to SHELL ->GEOCLOCK
<F1> = DATE FORMAT: mm-dd-yy <F4> = PRINT COLOR: 15
<F2> = PRINTER TYPE: Graphics <F5> = SCREEN COLOR: 1
<F6> = BORDER COLOR: ON
╒═ <F3> = RADIO: KENWOOD ════════════╕╒═ <F7> = TNC ═════════════════════╕
│ COM port number ->2 ││ COM port number ->1 │
│ Baud rate ->4800 ││ Baud rate ->9600 │
│ Parity (E/O/N) ->N ││ Parity (E/O/N) ->N │
│ Data bits (7/8) ->8 ││ Data bits (7/8) ->8 │
│ Stop Bits (1/2) ->1 ││ Stop Bits (1/2) ->1 │
│ Base Address ->2F8 ││ Base Address ->3F8 │
│ IRQ ->3 ││ IRQ ->4 │
╘════════════════════════════════════╛╘══════════════════════════════════╛
For each item on the menu, the values to the right of the arrow can be
changed. To do that, position the screen cursor to the line desired by
using the Up or Down arrow keys. When the cursor is on the desired line,
type in the new value and hit <Enter>.
CALLSIGN is used at the top of most screen displays and printouts.
LATITUDE/LONGITUDE is used by the program to calculate beam headings.
Enter your station's latitude and longitude in degrees for both items.
Log-EQF defaults to a lat/lon in the central United States, until you
enter the location of your station.
CONFIGURATION PAGE 3.1
POWER LEVEL is the value automatically entered into your logbook for
transmitter power. You can override this default value at any time by
typing over the existing value.
HOURS TO ADD FOR UTC controls how the date and time for Log-EQF logbook
entries is determined. If the response to the menu item is "0", then the
time used for each log entry will be exactly the same as your computer's
clock time. If you enter any other number for this menu item, that number
will be ADDED (SUBTRACTED, if you enter a negative number), to the
computer clock to calculate the date and time used for logging entries.
This item enables you to keep your computer clock on local time, and have
your logbook times in UTC.
LOGBOOK NAME is the name of the logbook file you will want to use for most
of your logging. The name you enter here will appear when you run Log-EQF
each time, so you don't have to type it in yourself. If you leave this
setup item blank, the program will make up a name for you, based on the
current year, such as "1990LOG". You can type in a new name at any time,
no matter what option you decide on for this item.
<F3> RADIO and <F7> TNC are used to select the communication parameters to
be used by your radio and TNC, respectively. When <F3> is selected, a menu
presenting available radio manufacturer/model numbers will appear. If your
rig appears on the menu, just highlight the correct selection and hit
<Enter>. If your radio is computer-ready and doesn't appear, see Chapter 6
for instructions on configuring Log-EQF. You do not need to select a
specific model for your TNC, since Log-EQF acts as a generic "dumb
terminal" to these devices.
COM PORT NUMBER tells Log-EQF whether you are using a radio and/or TNC.
Enter a 0 in the respective box if you are not using a radio or TNC, or
enter a number between 1 and 4 for the serial port being used. The TNC and
radio must be on separate ports of course.
BAUD RATE sets the communication rate between your computer and your radio
and/or TNC. Your TNC and radio must be set to match the value you enter
here. Typical baud rates are 1200 and 4800. If your TNC is set for AUTO
baud rate, it will be necessary for you to go to the full-screen terminal
emulation from the AUTOMATIC or MANUAL LOGGING screen using <F8>, and then
"wake up" the TNC when prompted. Consult the manufacturer's documentation
for directions on setting baud rate for your particular model.
PARITY, DATA BITS, STOP BITS are set to match the communication parameters
required by your radio and TNC. The default values for No parity (N), 8
data bits, and 1 stop bit are the most common. NOTE: Your TNC should also
be set for ECHO ON, so that characters you type will be displayed.
ADDRESS and IRQ must be set to match your computer's configuration for the
serial (COM) port(s) in use by your radio and TNC. Log-EQF will enter
values automatically for these parameters any time you change the port
number. If you are not sure what the address and interrupt parameters are
CONFIGURATION PAGE 3.2
for your computer, consult the documentation for your system or check the
settings in use by any other programs you use for COM port communication.
PROGRAM NAMES for SHELL is used to enter program names which can be
accessed from Log-EQF's Main Menu. You can use this feature to access
often-used programs through Log-EQF.
If the program you want to run cannot be located in the same directory as
Log-EQF, you can prepare a small file called a BATCH file to execute it.
Your BATCH file (consult your DOS manual for information about creating
BATCH files) would perform a DOS "CD" command to change directories to the
one where your program resides, and then "CALL" that program. Once you
have created your BATCH file, store it in the same directory as Log-EQF,
and specify the BATCH file's name on this item on the SETUP menu.
You can append the program name you supply for the SHELL with special
parameters which are passed to that program from Log-EQF's logging screen.
The available parameters are %C, %F, and %T, for Callsign, Frequency, and
Track, respectively. If you supply DX-EQF %C for the program name to SHELL
to, and you just entered 9X5AA as the callsign on the Log-EQF logging
screen, the DX-EQF program module (available free to Registered Users)
will check your DXCC status for that country automatically. Another
possibility would be to use the %C parameter with the name of a "CALLBOOK"
routine, to look up QSL information for the station you just worked.
If you have about 200K of Expanded Memory available on your computer, Log-
EQF will attempt to relocate itself into that memory space, so that
conventional "DOS" memory is freed for use by other programs. To find if
Expanded Memory is in use with Log-EQF, select SHELL to DOS, and check for
a message "EMS in use" at the upper right corner of the screen. Consult
your DOS manual for configuration of memory drivers such as "EMM386.EXE".
DATE FORMAT is accessed using the <F1> key, and can be used to change the
format of the date entries in the log. A menu will be displayed which
presents the available formats.
PRINTER TYPE can be standard, graphics, or a disk file. If your printer is
an Epson, or emulates the Epson graphics character set, select "GRAPHICS".
If your printer prints strange characters instead of lines from Log-EQF,
select "STANDARD". The third selection is labeled "DISK FILE". You may
use this option to direct print operations into a disk file, for use by
other programs (such as word processors) for formatting. Log-EQF will
ask you to enter a file name to be used each time you begin printing.
If your system has a color adapter and monitor, you can customize colors
which Log-EQF displays for background and characters. Hit the <F4>, <F5>,
and <F6> keys on your keyboard, and the display will update to show you
the current color selection.
- When all parameters on the configuration menu screen are set, hit the
<Esc> key again to save all the values to a disk file called LOG-EQF.CNF.
LOADING PAGE 3.3
- LOADING LOGBOOK FILES
---------------------
The first step in operation of Log-EQF (once the configuration setup
is complete) is to tell the program the name of the logbook file to be
used. The following menu is displayed by Log-EQF:
╒═══════════════════════ N3EQF Amateur Radio Logbook ═════════════════════╕
│ Entries In Log = 2091 Last Entry = VP25EI │
╘═════════════════════════════════════════════════════════════════════════╛
╒═══ LOAD LOGBOOK ENTRIES ════════════════════════════════════╕
│ │
│ │
│ Enter an existing or new log name below, or hit <─┘ │
│ to load the file shown. │
│ │
│ Enter logbook name: NEWLOG │
│ │
╘═════════════════════════════════════════════════════════════╛
╒═════════════════════════════════════════════════════════════╕
│ <F1> = CONTEST / DXpedition MODE │
│ <F2> = CONFIGURATION │
│ <F3> = SHOW AVAILABLE LOGBOOKS │
│ <F4> = RENAME TRACK FIELD │
│ <F5> = MAKE BACKUP OF NEWLOG FILES │
╘═════════════════════════════════════════════════════════════╛
═════════════════════════════════╡ Memory enough for 22701 more QSOs ╞══
Log-EQF will prompt you to "Enter logbook name", display a log file name,
and then wait for your response. If the name that is displayed is the
logbook you want to use, just hit <Enter>. (This is what is known as a
DEFAULT value, meaning if you don't type in new information, the program
uses the old information that is displayed on the screen). If this log
already exists, the program will read all the entries from that file. If
the log name is a new one, you will be asked if you want to create a new
log file on the disk.
If you want to use a file name other than the default, you may type it in
and then hit <Enter>. Note that logbook names cannot be longer than 8
characters (plus ".LOG").
A sample logbook file should be present on your Log-EQF disk.
This file may be used to demonstrate the features of Log-EQF, and for
experimentation until you become familiar with the program's operation.
To load this sample file, type "SAMPLE" at the prompt.
LOADING PAGE 3.4
The default file name is determined by information supplied by you from
the Configuration Setup menu. If you supplied a logbook file name on the
Configuration Setup menu line for "Logbook name most often used", then
that name will be used by Log-EQF each time you run the program. If you
didn't supply a default name (left the item blank), the first 4 characters
of the file name are taken from the last 4 characters of the computer
clock's date variable. The last 3 characters are always "LOG". If the
current date is 1990, the default file name is "1990LOG".
NOTE: If you wish to load data from a disk other than the one running
Log-EQF currently, you may proceed the file name with the disk assignment.
For example, if Log-EQF is being run from hard drive C, and you wish to
load logbook data from floppy drive A, file 1990LOG, then you would enter
"A:\1990LOG" from the prompt. This will remain the logbook file which is
viewed, edited, sorted, searched, or entered into by Log-EQF, until you
enter a new name.
You may also access another logbook by hitting the <F3> function key.
This will display all available logbooks in the current disk directory,
and allow you to choose the one to be loaded. You can also view the log
files in another directory from this screen.
The <F4> function key has a very special purpose. With it, you can
customize the logbook to contain a field you name yourself. This field is
called "TRACK", unless you call it something else. You could call this
field "COUNTY", or "10-10", or any other name to describe something you
want to keep track of in your logbook. Whatever name you give it, this
field will stay associated with the logbook to be loaded. You can name
different fields for different logbooks, depending on your operation.
Although you don't necessarily care, the name of this field is stored in a
separate disk file, which starts with the same name as the logbook, and
ends with ".TRK".
The <F5> key gives you an easy way to backup the current (displayed)
logbook files onto either a floppy drive or another disk directory on the
current drive. When <F5> is pressed, you will be asked where you want the
backup files to be copied. You can enter "A:" or "B:", for instance, to
have the backup created onto a floppy disk. Log-EQF will copy all the
files associated with the logbook name currently entered to the disk or
directory that you specify. Log-EQF uses the DOS external command called
BACKUP, which allows you to backup logbooks that are too big to fit onto
a single disk. You will be prompted to insert additional floppies as
required. Be sure to label your disks in the order they are backed up.
If you need to recover your logbooks from the backups, use the DOS
command called RESTORE. See your DOS User's Guide for instructions.
QUICK START PAGE 3.5
- QUICK STARTUP OF LOG-EQF
------------------------
A shortcut is available to allow you to start the program and load the
logbook file faster. To take advantage of this feature, you need only know
in advance what logbook name you are going to be using. Instead of typing
"Log-EQF" and hitting <Enter>, follow the program's name with a space, and
the name of your logbook file. For example, if you want to do a "quick
startup" using the SAMPLE logbook, type:
LOG-EQF SAMPLE <Enter>
When you use the "quick startup" method, the program will not display
the Welcome Screen or pause for you to hit a key to continue. If you
are using a radio interface, the radio and interface should be turned on
before you start the program. You will also not be prompted to enter
the name of logbook file to be loaded. Instead, Log-EQF will auto-
matically load the logbook you entered when you started the program.
When the logbook loading is complete, the Main Menu will be displayed,
and program operation will revert to normal.
You may also specify the program to startup in CONTEST mode by supplying
" /C" after the log filename from the command line. The following line
would cause Log-EQF to present the contest SETUP MENU and then load the
file TEST.LOG:
LOG-EQF TEST /C <Enter>
Another command line option forces Log-EQF to use the display options for
MONOCHROME computer displays. To do this, add " /M" after the other
command line parameters. For example:
LOG-EQF TEST /C /M <Enter>
One remaining option can be used to associate the configuration file used
by Log-EQF with the logbook file. (Normally, Log-EQF reads a file called
LOG-EQF.CNF for configuration information). To load a logbook called
SPECIAL, and create a configuration file called SPECIAL.CNF, type:
LOG-EQF SPECIAL /L <Enter>
CALLSIGN DATABASE SYSTEMS PAGE 3.6
- CALLSIGN DATABASE SYSTEM INTERFACES: "HAMCALL" CD-ROM OR "SAM"
----------------------------------------------------------------
1). "SAM" by RT Systems:
Log-EQF will interface with the SAM Amateur Radio Callsign Database
System, by RT Systems, so that the NAME, CITY, STATE, and optionally the
COUNTY logbook fields will be filled in automatically as soon as a
CALLSIGN is entered in the log. To enable this feature, you must use the
"Application Program Interface" routine called SAMAPI that is supplied
with the SAM product. The SAMAPI program must be started before running
Log-EQF. When you start Log-EQF, the SAM interface will automatically be
enabled. There is nothing else required to enable this feature.
At the time of this writing, SAMAPI must be started and the disk drive and
directory where SAM is installed must be supplied as an argument. In other
words, if SAM is installed on your C: drive, in a directory called SAM,
then you would type:
C:\SAM\SAMAPI C:\SAM <Enter>
This command must be typed before you run Log-EQF. You could either
include the command in your AUTOEXEC.BAT file, or write a batch file to
start Log-EQF after activating SAMAPI. Please consult your SAM User's
Guide for specific information about SAMAPI, or contact RT Systems.
2). "HAMCALL" by Buckmaster Publishing:
Log-EQF will automatically interrogate your system to see if the HAMCALL
system is installed each time Log-EQF is started. Therefore, if you want
to have Log-EQF retrieve the name and QTH information from HAMCALL, your
CD-ROM must be on-line with the Buckmaster HAMCALL disk installed before
you start Log-EQF. To utilize HAMCALL, just hit the <F5> INFO key on the
logging screen.
MAIN MENU PAGE 4.0
4. MAIN MENU COMMANDS
------------------
After a logbook has been loaded (or created), a menu will be displayed
with 14 items for selection. To select an item, use the arrow keys or
the mouse to change which item is highlighted. When the desired item is
highlighted, hit the <Enter> key to select that item. The Log-EQF Main
Menu screen appears below:
╒═══════════════════════ N3EQF Amateur Radio Logbook ═════════════════════╕
│ Entries In Log = 2091 Last Entry = VP25EI │
╘═════════════════════════════════════════════════════════════════════════╛
┌───────────────────────────────────┬─────────────────────────────────────┐
│ VIEW in DETAIL entries in logbook │ LOAD new logbook entries from disk │
│ │ │
│ QUICK VIEW entries in NEWLOG │ SORT logbook file by any field │
│ │ │
│ PRINT logbook record pages │ SEARCH log - Print/File/QSL options │
│ │ │
│ QSL LABELS output to printer │ NORMAL mode - switch for CONTEST │
│ │ │
│ LOG new entries - AUTOMATIC mode │ RUN ANOTHER PROGRAM │
│ │ │
│ LOG new entries - MANUAL mode │ SETUP program configuration │
│ │ │
│ EDIT an entry - based on callsign │ EXIT from program │
└───────────────────────────────────┴─────────────────────────────────────┘
╔═══════════╗
║ 22:34:10 ║
═════════════════════════╡ Log-EQF MAIN MENU ╞════════════════╚═══════════╝
Selection of a menu item will, depending on the type of operation
selected, display another menu, prompt you for some further information,
or switch the selected item to display some other item.
No matter which item is selected, hitting the <Esc> key will again
display the Main Menu.
The following paragraphs discuss the operation of each item on the Main
Menu.
VIEW IN DETAIL PAGE 4.1
- VIEW in DETAIL entries in logbook
---------------------------------
Selecting this item will display the first screen of entries contained
in the current logbook. One screen page in this mode contains 5 QSO's,
unless notepad entries are present. The number of QSO's on each screen is
automatically adjusted by the program to display notepad entries.
The format of this display consists of at least three lines for each
QSO, showing the complete details for each entry:
CALLSIGN CITY DATE START TIME SENT REPORT QSL
NAME STATE FREQ. END TIME RECEIVED RPT MODE POWER
QSO # TRACK COUNTRY INFORMATION...
As soon as the first screen page of entries is displayed, several options
are available, and these options are explained on the bottom line of the
screen.
If NOTEPAD information exists for a logbook entry, that information will
be displayed immediately following the standard three-line entry.
Selecting the <F1> function key activates the EDIT option. The program
will prompt you to enter a QSO number for the log entry you wish to edit.
Selecting the <Esc> key causes the VIEW in DETAIL mode to be stopped, and
the Main Menu will be displayed again.
The <Page Up> and <Page Down> keys may be used to scroll through the next
five entries, or the previous five entries in the log. The <Up Arrow> and
<Down Arrow> keys have the same effect, except the log entries scroll
forward and backwards one at a time.
At any time while scrolling through the log entries, you may select <Esc>
to return to the Main Menu.
QUICK VIEW PAGE 4.2
- QUICK VIEW entries in logbook
-----------------------------
Selecting this item causes display of a page containing abbreviated, one-
line entries for the first 23 QSO's in the current logbook. This mode
allows you to browse quickly through the log. The format of each entry
line is:
DATE TIME CALLSIGN FREQ MODE SENT RCVD QTH NAME QSL
To advance to the next page of 23 QSO's, just hit a key. To start over
again at the first page of 23 QSO's, hit the <Home> key. The <End> key
may be used to jump to the end of the logbook. The <Up Arrow>, <Down
Arrow>, <Page Up>, and <Page Down> keys may be used to scroll through
the log entries in either direction.
To return to the Main Menu, hit the <Esc> key.
PRINT LOGBOOK PAGE 4.3
- PRINT logbook record pages
--------------------------
This menu item allows you to print some or all of the current logbook,
using either the same format as is displayed on the screen during the
VIEW IN DETAIL option, or the shorter format as used during the QUICK
VIEW option.
A two-window menu appears, enabling you to either print all the QSO's in
the logbook, or to print any series of QSO's. To select an item in the
top window, highlight it by using the arrow keys and hit the <Enter> key.
╒════ Logbook Print ══════════════════════════════╕
│ │
│ Print ALL QSOs in the logbook file │
│ │
│ Print QSOs from number [ 1 ] to [ 2459 ] │
│ │
│ Print from dates [10Mar71 ] to [20Nov92 ] │
│ │
│ Print any QSOs marked `P' in QSL STATUS │
│ │
╘═════════════════════════════════════════════════╛
╒════ Selected Format ════════════════════════════╕
│ │
│ SINGLE LINE... hit <F1> for DETAILED │
│ │
╘═════════════════════════════════════════════════╛
When the "Print QSO's from number [ ] to [ ]" option is selected, enter
the first QSO number, hit <Enter>, then enter the last QSO number to be
printed. The default numbers for these are the first and last entries in
the logbook. You may alter either one of both of these numbers or just
hit <Enter> to accept a default value. Another menu item allows you to
print entries between any two dates.
To switch between the short and long print formats, use the <F1> key until
the desired format type is displayed in the bottom menu window.
After you have made your selections, hit the <Enter> key. The program
will prompt you to prepare the line printer and hit any key to begin
printing.
The printed page is setup to accommodate standard 8-1/2 x 11 inch paper.
If you elect to keep your printed logbook in a 3-ring binder, a few QSO
numbers may be lost when the paper is punched, since the numbers appear
on the extreme left edge of the page. Most printers will allow you to
shift the paper position to the left far enough to allow the logbook
pages to be punched without interfering with the printed information.
QSL LABELS PAGE 4.4
- QSL LABELS output to printer
----------------------------
Select this item to print QSL labels for all or part of the QSO's in the
current logbook. The selections available for this option are the same as
for the "PRINT logbook" option described above.
╒═ Label Options ═════════════════════════════════╕
│ │
│ 5-line standard 3.5 x 15/16 inches │
│ 5-line graphic 3.5 x 15/16 │
│ 5-line standard 3.5 x 1.5 │
│ 5-line graphic 3.5 x 1.5 │
│ 1-line standard 5 x 7/16 │
│ │
╘═════════════════════════════════════════════════╛
The "LABEL OPTIONS" menu allows you some controls over the appearance and
size of the QSL labels to be printed. There are three basic styles; two
with 5-lines of text to be printed, and one which prints the QSL info on
a single line. The single line text is printed on a label measuring 5"
x 7/16", in the following format:
CALLSIGN DAY MONTH YEAR TIME BAND RST MODE
This 1-line style will easily fit below the labeled columns on pre-printed
QSL cards. The two 5-line styles fit on larger labels, either 3.5 x 15/16"
or 3.5 x 1.5". A "graphic" selection is available, which will print solid
lines and double-wide callsign fonts if your printer is capable of
printing graphics characters.
NOTE: If you use a laser printer, make sure your printer is set manually
for 60 lines of text for a 10-inch page length, or 6 lines per inch. If
you need to adjust the top or left side margins to align labels with your
printer, select <F1> to enter appropriate margins, and <F2> to enter the
number of labels on each page. Use <F3> to test the current settings.
If you select one of the 5-line styles, the program will prompt you to
enter text to appear on the bottom line of the QSL label(s) to be printed.
The text you enter will be automatically centered on the bottom line of
the QSL label(s). This text line is limited to a length of 35 characters.
Another option for QSL label printing concerns automatic updating of the
QSL status field for each log entry being confirmed. If you select this
option when prompted, Log-EQF will mark a "S" in the QSL status field if
the field was empty, or it will mark a "X" in the QSL status field if it
previously contained a "R". Note that this is the system for tracking QSL
status within Log-EQF: S = Sent / R = Received / X = Exchanged QSLs.
Finally, if you have the SAM Callsign Database installed, Log-EQF will
give you the option to have address labels printed for each QSL label.
AUTOMATIC LOGGING PAGE 4.5
- LOG new entries - AUTOMATIC mode
--------------------------------
This menu item selects the automatic logbook update function. This mode
enables you to enter new entries into the logbook in "realtime", during a
QSO.
The function is called AUTOMATIC since the Date, Start Time, and End Time
for each QSO are taken from the computer clock. If you have the Kenwood
radio interface connected, the Frequency and Mode fields are also
automatically logged.
Below is a view of the Log-EQF AUTOMATIC LOGGING screen:
╒════════════════════════════════════════════╤═════════════════════════════╕
│ CALLSIGN -> ░░░░░░░░░░░░░░░░░░░ │ 16:50:14 12-31-92 (13:50) │
│ ────────────────────────────────────────── │─────────────────────────────│
│ REPORT SENT -> ░░░░░░░░░░░░░░░░░░ │ FUNCTION: AUTOMATIC ENTRY │
│ REPORT RCVD -> ░░░░░░░░░░░░░░░░░░ │ OPERATOR: N3EQF │
│ ────────────────────────────────────────── │ Log-EQF Version 5.0 │
│ NAME -> ░░░░░░░░░░░░░░░░░░░░░░░░░ ╞═════════════════════════════╡
│ CITY -> ░░░░░░░░░░░░░░░░░░░░ │ <F1> Save QSO 2460 │
│ STATE -> ░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ │ <F2> Log Start Time │
│ COUNTRY -> ░░░░░░░░░░░░ │ <F3> Edit Log: LOGBOOK │
│ ────────────────────────────────────────── │ <F4> Clear Screen │
│ FREQUENCY ->21.134.00░ VFO A ░ 14.147.80 ░ ├─────────────────────────────┤
│ MODE ->CW ░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ │ <F5> Info on DX Prefix │
│ POWER LEVEL ->100 ░░░░░░░░░░░░░░░░░░░░░░░░ │ <F6> Notepad Entry │
│ ────────────────────────────────────────── │ <F7> Run Another Program │
│ 10-10 -> ░░░░░░░░░░░░░░░░░░░░░░ │ <F8> Terminal / Scrollback │
│ QSL STATUS -> ░░░ QSL Codes: S/R/X/P ░░░░░ │ <F9> PacketCluster (tm) │
│ INFO -> ░ │ <F10> KENWOOD Control │
╞════════════════════════════════════════════╧═════════════════════════════╡
│W3IXR BBS Enter Command: A,B,C,D,F,H,I,JA,L,M,O,R,S,T,U,V,W,X,Y,?=help> │
│b │
│You have been connected 3mn 55s - Computer-time : 1s │
│73 Tom, and please come back. │
│ │
│*** DISCONNECTED │
└──────────────────────────────────────────────────────────────────────────┘
This view of the logging screen shows a Kenwood transceiver (VFO and MODE
display) and a TNC (box on bottom) interfaced to the program.
A full-screen display shows entry lines for CALLSIGN, REPORT RECEIVED,
REPORT SENT, NAME, CITY, STATE, COUNTRY, FREQUENCY, MODE, POWER LEVEL,
TRACK, QSL STATUS, and INFO. These fields may be entered in any order, by
using the <Up> or <Down> arrow keys to position the cursor on the desired
line. Also, the <Enter> key can be used to step through the lines without
affecting any information already entered.
AUTOMATIC LOGGING PAGE 4.6
The keyboard edit keys may also be used to make corrections to any of the
text already entered, so the entire line does not have to be retyped.
Position the cursor on the line to be corrected, then move the cursor over
the character desired using the <Left> and <Right> arrow keys.
To delete a character, position the cursor over the character and depress
the <Delete> key. To insert additional information between characters,
depress the <Insert> key and type in the additional characters. You may
deselect the insert mode by again depressing the <Insert> key, or it will
automatically be deselected when you move the cursor to another line. When
the <Insert> function is active, the cursor will change from a square to
a single line.
The <Home> key may be used to position the cursor back to the beginning of
a line when you have already moved the cursor to within the line. The
<End> key positions the cursor at the end of current text on any line.
Various function keys, plus the <Esc> and <Alt> keys provide control over
logbook operations:
<F1> is used to save the logbook entry to the disk file, after all logbook
information has been supplied. If a valid callsign has not been
entered, no action will be taken. When <F1> is selected, the current
log clock time is logged as the QSO END TIME. If <F2> had not been
selected previously, then the QSO START TIME will be logged as the
current clock time also. A message will be displayed confirming the
log entry was saved.
<F2> is used to LOG START TIME of QSO from the computer clock. When the
key is depressed, the current time is logged as start time. Each
time <F2> is pressed, the current time will be logged again. This
overrides the QSO start time which is entered automatically every
time a new callsign is entered.
<F3> allows you to update any recent QSO entries in the logbook. This
feature can be used during a roundtable QSO to fill in details for
any of the stations in the group.
<F4> may be selected to clear all information displayed on the screen.
When the key is pressed, the program will prompt you to verify you
want to clear the screen. If you respond with anything other than
"Y" for yes, the entry in progress will not be cleared.
<F5> may be selected to lookup DXCC information based on the prefix of
the callsign currently entered. The DXCC prefix, country name, CQ
and ITU zones, continent, and beam heading are displayed in a box
below the Log Keys box.
<F6> is used to enter information into the NOTEPAD for a log entry. The
NOTEPAD is located in the window at the bottom of the logging
screen. To complete the entry in the NOTEPAD, hit the <F1> key.
AUTOMATIC LOGGING PAGE 4.7
<F7> is used to run another program while Log-EQF remains resident in
memory. A pop-up menu will appear which presents a choice of running
one of the two SHELL programs you specified on the SETUP MENU, a
third program or command to execute, or returning to DOS.
If you choose to go to DOS, you can execute any DOS commands you
like, and when you are ready to return to Log-EQF, just type "EXIT".
The Log-EQF log entry screen will reappear, just as you left it.
Any other program to be executed from Log-EQF must either be in the
current disk directory, in the DOS "PATH", or have a batch file in
the current directory to perform a directory change.
<F8> is used to enter the full-screen TNC terminal emulation. Also, the
window at the bottom of the logging screen will monitor activity on
your TNC, if you have enabled the TNC option on the SETUP MENU. If
you see information scroll past this window, and would like to see
the information you missed, use the <F8> key to display the last 23
lines of text. You may even scroll back through previous text by
using the <Page Up> key.
<F9> is used to access the PacketCluster (tm) screen, which shows the 15
most recent DX spots, along with a window to make your own DX
announcement over the PacketCluster. To work a spotted DX station,
just position the highlight bar to the corresponding announcement and
hit <Enter>. The frequency will be set into your radio automatically
if one is interfaced, a DX INFO lookup will occur, and the logging
screen will be presented with the callsign entered in the CALLSIGN
field.
To make a PacketCluster announcement, hit the <F1> key, enter a
comment if desired, and hit <Enter>. You must be currently connected
to a PacketCluster node in order to make an announcement, of course.
See section 7 of this manual for more information about using
PacketCluster with Log-EQF.
<F10> is only active if a Kenwood radio is interfaced to your computer, and
the Rig-EQF program resides in the same disk directory as Log-EQF.
The Rig-EQF program provides advanced computer control features for
your Kenwood rig. (Rig-EQF is available as shareware from N3EQF).
<F11> and <F12> function keys may be used to SHELL from Log-EQF to another
program. These two programs are in addition to the ones you specify
on the SETUP menu. When you hit <F11>, Log-EQF will run a disk file
called SHELL11.BAT. The <F12> key will run a batch file called
SHELL12.BAT. You can setup these two files to activate programs you
might find useful while logging, such as a grayline map or satellite
tracking routine. Edit the two batch files using a text editor, and
keep them in the same disk directory as Log-EQF.
AUTOMATIC LOGGING PAGE 4.8
<Esc> may be used to return to the Main Menu, the same as with the other
program screens. You can do this at any time, without losing any of
the information currently entered into any of the logbook fields for
a new entry. Note that no information in this case will be
permanently saved, however, until <F1> is selected to add the entry
to the current logbook file. Each time a new callsign is entered
into the CALLSIGN field, the logbook is automatically searched to see
if that station has been worked before. If it has been, information
from your most recent QSO with the station will be entered for you by
the program in the NAME, CITY or COUNTRY, and QSL fields.
<Alt> may be used to control which of the logbook items you want to fill
in, instead of using the <arrow> keys to position the cursor on the
screen. When you first press the <Alt> key, one letter of each of
the logbook items on the screen will be highlighted. If you again
press and hold the <Alt> key, and then press the letter key
corresponding to the letter highlighted in the item you desire, the
cursor will immediately jump to that item. Entering information into
the log from this point is exactly the same as if you had positioned
the cursor to the item using the <Enter> or <arrow> keys. If you
already know the letter code for the item you want to select, you can
press and hold the <Alt> key along with the correct letter to select
that item. For example, if the cursor is located at the CALLSIGN
item, and you want to enter the signal REPORT RECEIVED, you can press
the <Alt> and "R" keys together and the cursor will move to that item
immediately.
The <Alt> key method of entry described above gives you a faster way
to jump from item to item using fewer key strokes. This feature is
enabled for both AUTOMATIC and MANUAL log modes, but is not available
in CONTEST mode.
<Alt-T> is used to start, reset, or turn off a 10-MINUTE IDENTIFICATION
REMINDER. This feature is enabled only in the AUTO log mode, and
when active it will display at the top of the screen the time
remaining until identification is required. After 10 minutes, a
visual and aural alert will remind you to identify. The timer will
reset automatically every 10 minutes, until you reset or stop the
timer by hitting the <Alt-T> keys.
MANUAL LOGGING PAGE 4.9
- LOG new entries - MANUAL mode
-----------------------------
The manual logbook entry page may be used to update a logbook "off-line",
after the QSO has already taken place. The manual entry mode can be used
to enter information into Log-EQF from previous logbooks.
╒════════════════════════════════════════════╤═════════════════════════════╕
│ CALLSIGN ->W1AW ░░░░░░░░░░░░░░░░░░░ │ 16:50:14 12-31-92 (13:50) │
│ ────────────────────────────────────────── │─────────────────────────────│
│ REPORT SENT ->599 ░░░░░░░░░░░░░░░░░░ │ FUNCTION: MANUAL ENTRY │
│ REPORT RCVD ->579 ░░░░░░░░░░░░░░░░░░ │ OPERATOR: N3EQF │
│ ────────────────────────────────────────── │ Log-EQF Version 5.0 │
│ NAME ->JOHN ░░░░░░░░░░░░░░░░░░░░░░░░░ ╞═════════════════════════════╡
│ CITY ->NEWINGTON ░░░░░░░░░░░░░░░░░░░░ │ <F1> Save QSO 2460 │
│ STATE ->CT ░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ │ <F2> Log Start Time │
│ COUNTRY ->USA ░░░░░░░░░░░░ │ <F3> Edit Log: LOGBOOK │
│ ────────────────────────────────────────── │ <F4> Clear Screen │
│ FREQUENCY ->3.53 ░░ DATE ->27Nov91 ░░░░ ├─────────────────────────────┤
│ MODE ->CW ░░░░░░░░░░░ TIME ON ->02:57:23░ │ <F5> Info on DX Prefix │
│ POWER LEVEL ->100 ░░░░ OFF at -> : : ░ │ <F6> Notepad Entry │
│ ────────────────────────────────────────── │ <F7> Run Another Program │
│ 10-10 -> ░░░░░░░░░░░░░░░░░░░░░░ │ <F8> Terminal / Scrollback │
│ QSL STATUS -> ░░░ QSL Codes: S/R/X/P ░░░░░ │ <F9> PacketCluster (tm) │
│ INFO -> ░ │ <F10> FREQ/MODE from radio │
╞═════╡ NOTEPAD Entry... Hit <Esc> when done ╧═════════════════════════════╡
│ │
│ John took a few moments to ragchew with me awhile! │
│ │
│ │
│ │
│ │
└──────────────────────────────────────────────────────────────────────────┘
This full-screen entry page is very similar to the AUTOMATIC mode, with
the following exceptions:
- Additional entry fields are provided for DATE, TIME ON, and TIME OFF.
Note that only the numerals need to be entered for date and time, and
Log-EQF will insert the ":" in the time and "-" in the date fields.
The <F2> function key may still be used, if desired, to put the
current UTC clock date and time into the DATE and TIME ON fields.
- The <F1> key will save the QSO information as displayed on the page,
but will not insert the TIME ON or TIME OFF fields. The date and time
information must be entered manually.
MANUAL LOGGING PAGE 4.10
- Defaults are provided for the REPORT RECEIVED and REPORT SENT fields
for each new QSO entry. If the mode entered is CW or FSK, both fields
default to "599". For all other modes the default report is "59".
- If the SENT or RECEIVED report fields are changed in format (from
"579" to "59", for example) Log-EQF will attempt to set the MODE
field to agree.
- When the <F4> function key is used to clear the screen, the DATE
field will remain at the last values entered. (The POWER, FREQUENCY,
and MODE fields will also remain at their last values, just as in the
AUTOMATIC entry mode).
- The FREQUENCY and MODE fields will not automatically update from the
radio when the interface is enabled, but the <F10> key may be used to
manually retrieve frequency and mode on the radio into the log fields.
EDIT LOG PAGE 4.11
- EDIT an entry - based on callsign
---------------------------------
This function is used to make changes to an existing entry in the logbook.
When the EDIT item is selected, the program will prompt you to enter part
or all of a callsign to be found in the log. Any number of characters may
be entered. If you enter a partial callsign, every log entry containing
that character pattern in the callsign field will be displayed. If you
enter a complete callsign, every log entry for that callsign will be
displayed. If only one callsign match is found in the log, the EDIT
screen will be displayed immediately.
If more than one callsign match occurs, all matching entries are displayed
and you will be prompted to enter the entry number to be edited. A number
will also be displayed in brackets ( [ ] ) indicating the last "match"
located, as a default value. If you depress the <Enter> key, the default
log entry will be edited; if you enter another number, that entry will be
edited.
Once you have selected the entry, a new screen will be displayed. The top
portion of the screen will show the logbook entry in full detail, as it
would be if the VIEW IN DETAIL option were selected. The bottom part of
the screen will display each field of the entry on a separate line. Each
line may be edited for the desired changes. Any time a change is made
to any line, the text on the line will be shown highlighted.
EDIT Entry # 176 N3EQF Amateur Radio Logbook
CALL/NAME QTH DATE/FREQ TIME ON/OFF SENT/RCVD QSL/MODE PWR
==========================================================================
KA3GBT Aliquippa 15Feb86 02:00:00 599 X
John PA 3.687 02:34:00 599 CW 100
╒═════════════════════════════════════════════════════════════════════════╕
│ CALLSIGN ->KA3GBT │
│ DATE ->15Feb86 │
│ START TIME ->02:00:00 ╒════════════════════════════╕ │
│ END TIME ->02:34:00 │ <Esc> = Back to MAIN MENU │ │
│ REPORT RCVD ->599 │ │ │
│ REPORT SENT ->599 │ <F1> = SAVE This Entry │ │
│ NAME ->John │ <F2> = DELETE Entry │ │
│ CITY ->Aliquippa │ <F3> = Next KA3GBT │ │
│ STATE ->PA │ <F4> = Edit ANOTHER CALL │ │
│ COUNTRY -> │ <F5> = NotePad │ │
│ FREQUENCY ->3.687 │ │ │
│ MODE ->CW │ <F7> = Print QSL LABEL │ │
│ POWER ->100 │ │ │
│ TRACK -> │ <Page Up> = EDIT # 175 │ │
│ QSL STATUS ->X │ <Page Dn> = EDIT # 177 │ │
│ INFO -> ╘════════════════════════════╛ │
╘═════════════════════════════════════════════════════════════════════════╛
EDIT LOG PAGE 4.12
When all the desired changes have been made, the edited entry may be saved
to the logbook disk file by selecting <F1>.
The <F2> key is used to delete an entry from your logbook. When the <F2>
DELETE key is selected, you will be prompted to make sure you really want
to delete the entry from the log. If you do not answer "Y" for yes, no
action will be taken.
If you elect to delete an entry using <F2>, the program will "mark" this
entry to be deleted, and wait for you to either select other entries to
delete or edit, or else exit the EDIT screen by hitting <Esc>. When you
exit the EDIT screen, Log-EQF will rebuild the logbook omitting any of
the entries you selected for deletion. Since entries are not truly
deleted from the log until you hit the <Esc> key, you can still recover
an entry marked for deletion by hitting the <F1> SAVE key before leaving
the EDIT screen.
To return to the Main Menu at any time during the edit session, hit the
<Esc> key. If you were doing a SEARCH when the EDIT was started, you
will instead be returned to the SEARCH in progress.
The <F3> key may be used to locate the next log entry for the callsign
currently displayed. If no other matching entries exist, the program
beeps.
The <F4> key allows you to select another callsign to edit, without the
need to return to the MAIN MENU.
The <F5> key may be used to edit the NOTEPAD for the current log entry,
if it already exists. You may then add to the existing notes, or create
a new NOTEPAD for the log entry. Hit <F1> when you are ready to leave
the NOTEPAD area and save the information. If you wish to delete an
existing NOTEPAD, you may use the <F6> key, which appears on the EDIT
screen only if a NOTEPAD already exists.
The <F7> key is used to print a QSL LABEL for the QSO currently displayed
on the EDIT screen. You will be returned to EDIT after the label is
printed.
The <Page Up> and <Page Down> keys may be used to leave the currently
displayed entry for edit, and instead edit the logbook entry preceding
or following it. You may "page through" all the logbook entries in this
way, until you find an entry to be edited.
After 10 entries have been edited, a backup logbook file will be created
for you (if there is enough room on the disk). Backup files are named
the same as regular logbook files, except the last three characters
after the "." (known as the file extension) are .BAK instead of .LOG.
LOAD LOGBOOK PAGE 4.13
- LOAD new logbook entries from disk
----------------------------------
Selecting this menu item will allow you to change the logbook disk file
from the current loaded file to another logbook file on the disk, from
another disk, or to create a new file.
Whatever file name you specify will become the file for which VIEW, EDIT,
SEARCH, SORT, or LOG functions operate on. The file which was in use
before you selected this menu item will remain on the disk, and will not
be acted on in any way until you again specify its name from this item.
You may hit <F1> to enter CONTEST mode, or <F2> to enter the CONFIG-
URATION SETUP MENU. The <F3> key can be used to display all available log
files in the current directory. A prompt will appear at the bottom of
this screen so you can enter the logbook filename of your choice.
The <F4> key can be used to customize the "TRACK" field for the logbook to
be loaded. This field name stays associated with the logbook until you
change its name.
Hitting the <Esc> key while the LOAD LOGBOOK ENTRIES FROM DISK screen is
displayed will return control to the Main Menu, and the logbook file name
in use before the item was selected will remain in effect.
(See "Loading Logbook Files" in Section 3 of this manual for more info).
SORT LOGBOOK PAGE 4.14
- SORT logbook file by any field
------------------------------
This menu item allows you to arrange the currently-loaded logbook file in
order based on the field of your choice.
A menu page is displayed which lists the fields which may be chosen for a
sort: CALLSIGN, DATE/TIME, FREQUENCY, MODE, CITY, STATE, COUNTRY, QSL
STATUS, TRACK, or INFO. You may also hit the <Esc> key to leave the Sort
Menu and return to the Main Menu.
╒═ Logbook SORT by:═══════════════╕
│ │
│ CALLSIGN │
│ │
│ DATE & TIME │
│ │
│ FREQUENCY │
│ │
│ MODE │
│ │
│ CITY │
│ │
│ STATE │
│ │
│ COUNTRY │
│ │
│ QSL STATUS │
│ │
│ TRACK │
╘═════════════════════════════════╛
The sort function can be useful in a number of instances. For example,
if you are interested in finding all the different countries worked, you
can sort the logbook according to the STATE or COUNTRY field. The sorted
log can then be printed, and each new country will be easier to spot,
since they will appear in alphabetical order.
If you enter logbook entries using the MANUAL mode that are earlier QSO's
than those already entered, you can sort by DATE/TIME to arrange the
logbook in chronological order.
SORT LOGBOOK PAGE 4.15
NOTE: The sort program is a very disk-intensive operation. The sort may
take considerable time to complete, depending on the size of the log
and the speed of the disk drive being used. A running-time display
is provided on the screen while the sort is in progress.
This sorting method was chosen to accommodate very large log files
without requiring massive amounts of memory.
When the sort is complete, you will be given the option of permanently
saving the sorted logbook. If you choose to save the sorted logbook, it
will be maintained in the sorted order the next time you load it from Log-
EQF. If you do not permanently save the sorted logbook, Log-EQF will use
an index file to display or print logbook entries in the order you chose
for the sort. A reminder message will appear at the lower left corner of
the MAIN MENU while the temporary sort remains in effect. As soon as you
load another logbook, the sort order will be removed, and the original
logbook file will remain unchanged.
Anytime you permanently save a sorted logbook, duplicate QSOs will be
automatically deleted. This can happen when multiple logbooks are merged
into one large one. A duplicate QSO is determined by matching callsign,
date, and time logged for multiple entries, when the logbook is sorted
by the date and time fields.
SEARCH LOGBOOK PAGE 4.16
- SEARCH logbook - Print/File/QSL Options
---------------------------------------
As the menu item suggests, there are options available for this function.
A menu screen is presented for selection of the desired option. The
options are as follows:
╒═ SEARCH results output to:══════╕
│ │
│ │
│ Disk File │
│ │
│ Screen │
│ │
│ Printer │
│ │
│ QSL Labels │
│ │
│ │
╘═════════════════════════════════╛
(1) Disk File - selecting this option causes the results of the search
operation to be stored in a disk file. You will be prompted to enter
the log name to be used, and prompted again if the name you enter
already exists. If the log exists, you can either APPEND (add) the
new search entries onto the end of the old file's entries, or REPLACE
the old file completely. The file stored using this option is a
complete logbook file, and may be loaded at any time by Log-EQF.
(2) Screen - this option displays the results of the search on the screen,
using the same format as the VIEW IN DETAIL function.
(3) Printer - this option dumps the search results to the printer in the
standard logbook format.
(4) QSL Labels - this option prints QSL labels from the search results,
using the usual format.
Once the output option is selected, another menu will be displayed, pro-
viding selections for which logbook field is to be searched.
After you position the highlight bar to the field you wish to search and
hit the <Enter> key, you have one option remaining. You can begin the
search in the selected field by hitting <Enter> again, or you can choose
a SECOND field in addition to the first one and then hit <Enter>. If you
choose to search two fields, any entry which matches BOTH patterns you
enter for each of them will be sent to the output.
SEARCH LOGBOOK PAGE 4.17
Certain guidelines for the search apply:
- For all fields except CALLSIGN, MODE, and STATE, the text you enter
will be matched as either upper or lower case letters, exactly as
entered. You can override this default, and ignore any differences
in capitalization for any field by hitting the <F1> key before the
search begins. By selecting this "IGNORE upper/lower case" option,
you will obtain a match for either "JOHN" or "John" if you search for
"JOHN" in the NAME field, for example.
- You can search through all logbooks instead of just the logbook that's
currently loaded, by selecting <F2> before the search begins.
- To search for empty fields (no information entered) hit only the
<Enter> key when prompted to "enter the pattern to be searched for".
- You can use "wildcard" characters to perform more accurate searches.
The wildcard characters are the same as those used by DOS commands;
"?" as a "don't care" position holder for single characters, and "*"
as the "don't care" condition for multiple characters. The following
examples illustrate the use of wildcards:
1) To search for all callsigns that begin with "N3" as the first
two characters, type "N3*" for the CALLSIGN field.
2) To search for all callsigns that end in "EQF", you could type
"???EQF" for the CALLSIGN field. If the calls N3EQF, WA3EQF,
and N9EQF are in your logbook, they would all be found by the
SEARCH.
3) To search for all callsigns with a "3" as the second
character, type "?3?????" for the CALLSIGN field. Callsigns
beginning with "N3" or "W3" would be found, but callsigns
that start with "WA3" or "WB3" would be missed.
- NORMAL/CONTEST mode select
--------------------------
This menu item is used to switch Log-EQF from a "routine QSO" logbook to a
contest logbook and back again. When the item is switched to the CONTEST
mode, the program automatically calls a subroutine which is used to select
the configuration "rules" to be followed during the contest.
When the item is selected when already in CONTEST mode, Log-EQF operation
returns to the normal mode. Each time the item is toggled back to the
contest mode, the contest setup menu will appear again, and the contest
configuration can be modified.
Operation of Log-EQF in the contest mode is described in Section 5 of this
manual.
RUN OR SHELL PAGE 4.18
- RUN ANOTHER PROGRAM
-------------------
┌─────────────────────── Select SHELL ─┐
│ │
│ Run: DX-EQF %C │
│ │
│ Run: GEOCLOCK │
│ │
│ Name another program to run... │
│ │
│ Go to DOS │
│ │
└──────────────────────────────────────┘
This item is selected to execute DOS commands, or run another program,
without leaving Log-EQF.
The file names you specified when the configuration file was established
(see Section 3) will be displayed with these items. When you hit <Enter>
to select either of the first two "RUN: " menu items, Log-EQF will attempt
to execute the program shown. The program specified must either be in the
same directory as Log-EQF, or be accessible in the current DOS PATH. The
DOS file COMMAND.COM must also be available in the root directory of the
current disk for the shell to take place.
The third line on the menu allows you to run another program besides those
specified on the configuration setup. Simply type the program name and
hit <Enter> to run the program. Again, COMMAND.COM and the program you
specify must be present on the current disk.
The last line on the SHELL menu is provided so you can temporarily return
to the DOS environment. Once you are ready to return to Log-EQF from
DOS, type "EXIT", and the Log-EQF Main Menu will appear.
If your computer has sufficient Expanded Memory installed, along with the
appropriate memory driver software, Log-EQF will automatically place
itself in this expanded memory during the shell. The Lotus/Intel/Microsoft
Expanded Memory Specification (EMS) requires that you have a memory driver
such as EMM386 installed. (The EMM386 driver simulates Expanded Memory
using your computer's extended memory). Consult your DOS manual, or your
computer's User Guide, for information about EMS.
You can quickly check to see if EMS memory is in use by Log-EQF. Just
select the "Go to DOS" SHELL menu item. If sufficient EMS memory is
available, you will see a message "(EMS in use)" displayed at the top
right side of the screen. If you see this message, you have all but about
25K of conventional (lower 640K) memory available to run other programs
while Log-EQF remains resident in EMS.
EXIT PAGE 4.19
- SETUP program configuration
---------------------------
Selecting this menu item causes the Log-EQF configuration setup menu to
appear on the screen. Operation of this setup menu is explained in
Section 3 of this manual.
- EXIT from program
-----------------
This item will cause a message to appear, asking you to confirm that you
want to exit Log-EQF, and return to the operating system. If you do not
answer "Y" for yes, no action will occur.
CONTEST OPERATION PAGE 5.0
5. CONTEST OPERATION
---------------------
- INTRODUCTION
------------
The CONTEST mode of Log-EQF provides a quicker way to enter the log
exchanges during a contest than the NORMAL mode. It also provides
ways to help you determine your score when the contest is over, and
generates a dupe check sheet to prove you have no duplicate contacts.
(Since duplicates are spotted by the program automatically during the
contest, you shouldn't have any dupes anyway!).
Log-EQF's CONTEST mode is also very useful for DXpedition or Special
Event operations. In CONTEST mode, Log-EQF displays a QSO/hour rate,
presents fewer logging fields (less clutter), and will announce those
"insurance contact" QSO attempts for the current band and mode. After the
event, you can use Log-EQF to print and record the sending of QSL's.
Please take time BEFORE the contest to read this section of the User's
Guide, to get familiar with Log-EQF's CONTEST mode. The program provides
you with several options, which you can choose from the CONTEST SETUP
MENU to fit the contest you will be operating. Once you have made your
selections (see the following pages), try logging a few "practice"
contacts before the contest starts. That way you will have time to change
any of the setup parameters without wasting precious time during the
event. Try printing the "practice" contest log to be sure it works the
way you want it to.
Log-EQF is designed so that it can adjust to many different types of
contests. It is NOT designed to print out a ready-to-send-in entry form
for any specific contests. Instead, Log-EQF is a "general purpose" program
that provides scoring assistance and dupe-checking. There are some fine
programs out there already setup to handle specific contests, should you
decide you need more contest power than Log-EQF provides. The FILE-EQF
utility that is available to registered users of Log-EQF can be used to
convert logbooks from the popular contest programs CT and NA into Log-EQF
logs after the contest. This allows you to combine CT or NA contest
logbooks into your daily Log-EQF logbook file(s).
One other note about the CONTEST mode concerns the Contest Entry Logbook.
For most contests, the Log-EQF printed log is suitable for submission
with your official contest entry. Log-EQF also stores a copy of the
Contest Entry Logbook on your disk drive, naming the file the same as the
logbook, except it will end in ".TXT" instead of ".LOG". This file is
stored in pure ASCII format, which means you may edit it using any Word
Processor program. If you need more information on the Contest Entry
Logbook than Log-EQF automatically provides, this is a way for you to
make changes, and then print the final logbook form to submit with your
entry.
CONTEST OPERATION PAGE 5.1
- CONTEST CONFIGURATION SETUP
---------------------------
When you select the CONTEST mode from the Log-EQF Main Menu, another menu
appears on the screen, which contains items specific to contest operation.
╒════════════════════════════════════════════════════════════════════════╕
│ LOG-EQF CONTEST SETUP MENU N3EQF │
╘════════════════════════════════════════════════════════════════════════╛
╒════════════════════════════════════════════════════════════════════════╕
│ │
│ Contest NAME ->ARRL 160 METER CONTEST │
│ │
│ Contest LOGBOOK NAME used most often ->ARRL160 │
│ │
│ Number of QSO's PER PAGE on printed results ->50 │
│ POINTS for each CW or FSK QSO ->2 │
│ POINTS for each Phone QSO ->0 │
│ Does each band worked require a SEPARATE DUPE SHEET? Y │
│ │
│ Enter the default REPORT to be SENT for exchange ->WPA │
│ Is there a SERIAL NUMBER sent as part of exchange? N │
│ │
│ Enter the default REPORT to be RCVD for exchange -> │
│ Enter MULTIPLIER FIELD title for RCVD exchange, if any ->SECTION │
│ │
╘════════════════════════════════════════════════════════════════════════╛
╒════════════════════════════════════════════════════════════════════════╕
│ Select the configuration parameters listed above │
│ and hit <Esc> key to save them in disk file CONTEST.ID │
╘════════════════════════════════════════════════════════════════════════╛
Once the contest setup is completed, you will be returned back to the Main
Menu. You may return to the contest setup menu to change any contest
parameters by switching to NORMAL mode, then back to CONTEST mode from the
Main Menu. This may be done before, during (with caution - it's easy to
make mistakes in the heat of battle!), or after the contest.
CONTEST OPERATION PAGE 5.2
Below is a description of each parameter available from the contest setup
menu:
(1) Contest NAME. The title you enter here will be used on the contest
logbook and dupe sheet printouts, and will also be automatically
entered in the INFO field of each entry in the contest log.
(2) Contest LOGBOOK NAME used most often. The name entered here will be
used as a default file name, displayed when the Main Menu LOAD item is
selected. The file name may have no more than 8 characters, and can-
not include a file extension (.LOG extension is automatically added).
You can include the entire "path" for your logbook file, which can
specify both the disk drive and a disk directory with the file name,
if you desire. If the disk directory you specify does not already
exist, Log-EQF will ask if you want to create the new directory.
(3) Number of QSO'S PER PAGE on printed results. Enter the number here
depending on the contest rules.
(4) POINTS for each CW or FSK QSO. Enter the points to be earned for
each "digital" QSO. This value will be automatically entered on
the logbook printout after the contest, for each non-duplicate CW
or FSK QSO, and totalled at the end of the log printout.
(5) POINTS for each PHONE QSO. Enter the points to be earned for
phone QSO's. As above, the score will be calculated for QSO points
based on the number provided here.
NOTE: If "0" is entered for BOTH the above POINTS items, the logbook
will be printed with only "____________" under the QSO POINTS
column, to allow for manual scoring, if desired.
CONTEST OPERATION PAGE 5.3
(6) Does each band worked require a SEPARATE DUPE SHEET? If a "Y" for yes
is entered here, Log-EQF will keep track of the band and mode for
each station worked. The same callsign worked on different bands and
modes will therefore not be flagged as a duplicate. If a "N" for no
is entered, you will be alerted each time you enter a callsign which
has already been worked, regardless of the band or mode.
Only one logbook file will be created for the entire contest, no
matter which option you choose for this item.
(7) Enter the default REPORT to be SENT for exchange. The default report
will appear on the log entry screen for each QSO, and may be over-
typed as needed. (Again, "default" means that the report displayed on
the screen will be logged if you don't change it).
(8) Is there a SERIAL NUMBER sent as part of exchange? If you enter "Y"
for yes, an automatically-incremented number will be appended to the
SENT report for each QSO (and displayed on the logbook entry screen).
(9) Enter the default REPORT to be RECEIVED for exchange. This default
report will appear on the log entry screen for each QSO, and may be
over-typed as necessary.
(10) Enter MULTIPLIER FIELD title for RECEIVED exchange. If a title is
entered here, an additional field will be available on the contest
log entry screen. This field may be used to log the part of the
received exchange that counts towards multiplier points, which will
make scoring easier after the contest. Anytime a contest requires
a longer receive report than the RECEIVED field can hold, use this
field to accept the information, with a length up to 12 characters.
If the MULTIPLIER FIELD is selected, it will be placed on the entry
screen just below the CALLSIGN field. The MULTIPLIER field should
usually be the one most likely to change with every QSO, while the
REPORT RECEIVED field will usually be the same (59 or 599) for every
QSO. If possible, limit the MULTIPLIER FIELD to that part of the
contest exchange which will be used to calculate the score. For
instance, many ARRL contests use the ARRL SECTION for a multiplier,
with the total sections worked being multiplied by QSO points for
the final score. In this case, the MULTIPLIER FIELD should be called
SECTION, and Log-EQF will calculate the total number of unique
sections logged.
CONTEST OPERATION PAGE 5.4
- OPERATION DURING THE CONTEST
----------------------------
The basic operation of Log-EQF during a contest remains similar to the
"normal" mode, except that certain features are streamlined for faster
operation, and some new features appear.
╒════════════════════════════════════════════╤═════════════════════════════╕
│ CALLSIGN ->KH6BR ░░░░░░░░░░░░░░░░░░░░░ │ 16:50:14 12-31-92 (13:50) │
│ ────────────────────────────────────────── │─────────────────────────────│
│ MULTIPLIER -> ░░░░░░░░░░░░░░░░░░░░░ │ FUNCTION: CONTEST ENTRY │
│ REPORT RCVD ->25 ░░░░░░░░░░░░░░░░░░░░░ │ OPERATOR: N3EQF │
│ ────────────────────────────────────────── │ Log-EQF Version 5.0 │
│ REPORT SENT -> ░░░░░░░░░░░░░░░░░░░░░ ╞═════════════════════════════╡
│ SERIAL NUMBER ->101 ░░░░░░░░░░░░░░░░░░░░░ │ <F1> Save QSO 2460 │
│ ░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ │ <F2> Printer ON │
│ ░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ │ <F3> Edit Log: LOGBOOK │
│ ────────────────────────────────────────── │ <F4> Clear Screen │
│ FREQUENCY ->14.070.91 ░ VFO A ░░░░░░░░░░░░ ├─────────────────────────────┤
│ MODE ->CW ░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ │ <F5> Info on DX Prefix │
│ POWER LEVEL ->100 ░░░░░░░░░░░░░░░░░░░░░░░░ │ <F6> Notepad Entry │
│ ────────────────────────────────────────── │ <F7> Run Another Program │
│ BAND: 20 Meter CW ░░░░░░░░░░░░░░░░░ │ <F8> Terminal / Scrollback │
│ SINCE LAST QSO: 0:03:21 ░░░░░░░░░░░░░░░░░ │ <F9> PacketCluster (tm) │
│ LAST 10 QSO RATE: 56 /hr ░░░░░░░░░░░░░░░░░ │ <Alt> Partial Call Check │
╘════════════════════════════════════════════╧═════════════════════════════╡
(1) Different LOG screen fields. Probably the most important changes are
on the LOG-AUTOMATIC and LOG-MANUAL entry screens. No matter what
selections you made when you setup the contest configuration, you will
see fewer lines for information entry on the screen. The NAME, CITY,
STATE, COUNTRY, POWER, and QSL lines do not appear in contest mode.
If you elected to use the MULTIPLIER field option when you configured
the contest, the title entered from the configuration menu will appear
on a separate line just above the REPORT RCVD line. The information
you enter here is automatically appended to the REPORT RECEIVED
information when the contest logbook is printed. The MULTIPLIER field
information is kept separate within the program's logbook data file.
(2) Automatic SERIAL NUMBER generation. If you selected the option to
create SERIAL NUMBERS for the contest exchange, a 3-digit serial
number will appear below the REPORT SENT line. This number will be
automatically incremented after each new QSO is logged, and will
be appended to the REPORT SENT information.
CONTEST OPERATION PAGE 5.5
(3) Realtime PRINT of each QSO. On the screen's LOGBOOK KEYS menu, key
<F2> controls the status of the printer during the contest. If you
toggle <F2> to get the printer "ON" message, the printer will output
the complete exchange every time you log a QSO. This feature is not
intended to generate a "presentable" contest logbook, but is provided
as a safety feature, in case Murphy decides to strike your computer
system in mid-contest! If you have a printer connected, I highly-
recommend you use this option.
(4) DUPE CHECKING. A dupe-check routine runs each time you enter a call.
If a duplicate is found, you will be greeted with an audio
"raspberry", and a corresponding message will appear. Note that you
always have the option of logging this contact anyway, even if it was
found to be in the log already. A duplicate callsign will not be
reported as a dupe, as long as that call was not logged on the current
band and mode. The current band and mode (either DIGITAL or PHONE)
will be displayed on the screen for you, so that you can be sure the
log agrees with your current radio mode and frequency. If you are
using a radio interface, this display will be updated automatically as
you change radio parameters.
(5) PARTIAL CHECK. This feature allows you to check part of a callsign to
see any callsigns in the log which could possibly match. For instance,
if you copy only "ABC" as the callsign, hitting the <Alt> key would
display any calls ending in "ABC" which were worked already.
(6) QSO RATE and LAPSE TIME DISPLAY. A box will be displayed to give you
progress information during the contest. A running timer shows how
much time has passed since the last QSO was logged. Another display
will track the rate (in QSO's per hour) of your last 10 QSO's. This
rate display will become active once you log more that 10 contacts.
CONTEST OPERATION PAGE 5.6
- OPERATION AFTER THE CONTEST
---------------------------
IMPORTANT: Always make a backup copy of your contest data files before
attempting to generate dupe sheets or log forms, in case
something goes wrong! Anyone who has worked with computers
for long will tell you it can and does happen eventually!
Several Main Menu items change their title and function when in the
contest mode of operation:
(1) PRINT contest entry logbook. This is the menu item used to generate
the logbook which is to be submitted with your contest entry. This
item also generates a disk file in true ASCII format, which contains
the same information as is printed.
(2) Run and Print DUPE CHECKSHEET. This menu item will create a duplicate
checksheet for each band/mode combination in the contest log. If you
selected "N" for the CONTEST SETUP MENU item concerning separate dupe
sheets for each band, only one dupe sheet will be created. It will
flag duplicate contacts based on callsign alone, so if the same
station is worked on different bands, it will be marked as a duplicate.
You will be given the option to print multiple copies of the DUPE
CHECKSHEET, and to create ASCII disk files from this same information.
Some of the parameters which affect the contest logbook printout are
controlled from the contest configuration menu. You can alter any of
these parameters after the contest is over, in order to change the
appearance of the printed log.
The number of QSO's per page, and the number of points for each
type of QSO, will change only the printed logbook, not the contents of
the logbook data file itself.
(2) Run and print DUPE CHECKSHEET. This operation is controlled completely
by Log-EQF. All that is required is that you load the logbook data
file for the contest being duped, select the Main Menu item, and
wait until prompted to turn on the printer. The printed dupe-sheet is
formatted to fit on 8-1/2 x 11 inch paper, and will be automatically
numbered and titled, with duplicates marked. The number of valid QSO's
(not duplicated) will also be printed at the bottom of the last page.
Again, a true ASCII file will be created on the disk.
RADIO INTERFACE OPERATION PAGE 6.0
6. RADIO INTERFACE DESCRIPTION
-------------------------------
Interfacing a computer-compatible radio to your computer introduces some
very convenient features to the Log-EQF program. Connecting the radio to
your computer requires a 3-wire (minimum) cable between one of your
computer's serial (COM) ports and the radio interface. Some radio models
have the interface built in, while others require an external level
converter. Please consult the appropriate manual for the specifics on your
radio.
NOTE FOR KENWOOD USERS: If your radio requires an IF-232C Level Converter,
you can build one easily, and for much lower cost, than the Kenwood unit.
An excellent construction article written by Gary Kalata, KC4ES, appeared
in September 1991 QST. The article, and a follow-up in the December 1991
QST "Feedback" column, describes a simple circuit you can build using a
hand-full of readily-available components.
Once the hardware connecting the radio and computer is operational,
Log-EQF requires a software configuration to tell it how the processor in
the radio exchanges information with the computer. In an ideal world, all
radio manufacturers would use the same interface specification, all rigs
would understand the same instructions, and the data transmitted from the
radio to the computer could be interpreted in the same way. In the real
world, even different models by the same manufacturer are sometimes not
compatible with each other! This is where the "programmable radio
interface" section of Log-EQF comes into play.
Log-EQF uses the information in disk files ending in ".RIG" to supply it
the information about the radio connected to the serial port. The files
which exist for specific radios are made available for selection from Log-
EQF's SETUP menu. Each file contains 40 lines of information, with each
line representing a parameter which affects the way Log-EQF handles
communication with the radio.
If your radio is "computer-ready" but no .RIG file exists for it, you can
create a new file using a text editor. The easiest way to do this is to
copy an existing file for a similar radio to a new file, then edit the new
file with the appropriate information. The parameters in the file are
divided by function, and must remain in order. Values for each parameter
must begin on column one of the file, with any comments about the
parameter positioned to the right of an exclamation point (!).
If you create a new radio file and the program doesn't seem to work right
with the radio connected, don't be surprised or discouraged. There are a
lot of parameters involved, and any one of them can be the source of
trouble if not correct. Analyze the symptoms carefully, and look at only
those file parameters which seem directly related (use my cryptic comments
next to each parameter as a guide). If neither the frequency or mode are
displayed on the AUTOMATIC logging screen, and typing frequency or mode
has no effect, check the communication parameters like baud rate, data and
RADIO INTERFACE OPERATION PAGE 6.1
stop bits, etc. first. If those are correct, check the parameters near the
top of the .RIG file. If some operations work but others don't,
concentrate only on the parameters grouped in the inoperative section of
the .RIG file. Remember to return to the Log-EQF SETUP menu each time you
change the .RIG file, so the changes you make are read by the program.
If you develop a .RIG file for a new radio, please help other users by
sending N3EQF a copy of the file.
EXAMPLE RADIO CONFIGURATION FILE:
---------------------------------
Icom IC-735 ! Model for display within Log-EQF --FIRST LINE IN FILE--
0.0 ! Update rate in seconds - or (M) for manual or (N) for none
! Acknowledge command, if required
6 ! Bytes received from radio for ECHO or OK block
! Pacing or Initialize command, if required
H ! Hexadecimal (H) or String (S) instruction data type
F ! Commands sent to radio Forward (F) or Reverse (R) order
! -------------- FREQUENCY READ -------------------------
FEFE04E003FD ! Command to receive operating FREQUENCY from radio
10 ! Number of bytes expected from radio after FREQ command
6 ! Starting byte position for FREQUENCY value
4 ! Number of bytes in FREQUENCY value
R ! Frequency decoded in Forward (F) or Reverse (R) order
B ! BCD (B) or Weighted Binary (W and scale) or BCD single (S)
! -------------- MODE READ ------------------------------
FEFE04E004FD ! Command to receive operating MODE from radio
7 ! Number bytes expected from radio after MODE command
6 ! Starting byte position for MODE value
1 ! Number of bytes in MODE value
! Bit mask for MODE value, if required
03 ! Value for CW
00 ! Value for LSB
01 ! Value for USB
05 ! Value for FM
02 ! Value for AM
07 ! Value for FSK
! -------------- FREQUENCY SET --------------------------
FEFE04E00500000000FD ! Command to set the operating FREQUENCY
6 ! Starting byte position for FREQUENCY value
4 ! Number of bytes in FREQUENCY value
! -------------- MODE SET -------------------------------
FEFE04E00600FD ! Command to set the operating MODE
6 ! Starting byte position for MODE value
1 ! Number of bytes in MODE value
03 ! Value for CW
00 ! Value for LSB
01 ! Value for USB
05 ! Value for FM
02 ! Value for AM
07 ! Value for FSK
RADIO INTERFACE OPERATION PAGE 6.2
RADIO CONTROL AND DISPLAY OPERATION:
-----------------------------------
Control and display of radio frequency and mode is available on the
AUTOMATIC logging screen. If the frequency or mode of the radio are
changed at the radio, Log-EQF will read and display the updated
information. When a QSO entry is saved into the logbook, the frequency
and mode displayed on the screen are automatically entered into the log
as well.
To control the radio frequency and mode from Log-EQF, just type the
desired value into the FREQUENCY or MODE field.
NOTES:
1). Some radios do not support all of the required interface instructions
instructions for complete exchange of frequency and mode. For example,
some radios cannot send information to the computer, but do allow control
of frequency or mode from the computer. Other radios send only
information from a VFO specified by the computer instruction, instead of
reporting the selected VFO. For these radios, the VFO must be selected at
the rig in order for the computer to receive the frequency and mode.
2). Some radios "hang up" all radio functions while transferring
information between it and the computer. For this reason, it is not
practical to perform these transfers automatically at a given time
interval. For these rigs, specify an "M" for the update rate. A function
key <F10> will be dedicated to retrieving the mode and frequency from the
radio into the logging fields.
3). Some radios cannot process data at high speeds, and may require a
delay between characters sent from the computer. Specify a number between
1 and 5 as the second parameter in the "update rate" line of the .RIG
file, to cause 1-tenth to 5-tenths of a second delay between characters.
A comma must separate the two items on this line; for instance a manual
update with a 0.3 second delay between characters would be specified as
"M,3".
4). A scale factor can be specified to calibrate frequency display
received from the radio. If the displayed frequency is 0.7 instead of
7.0, for example, you can specify a scale factor of 10. The scale factor
is the second parameter on the frequency read "type" line in the .RIG
file. For example, a radio requiring BCD frequency decode and a scale
factor of ten would need the line "B,10".
RADIO INTERFACE OPERATION PAGE 6.3
KENWOOD ADDITIONAL CONTROL FEATURES:
-----------------------------------
When a Kenwood radio is attached to your computer's COM port, control and
display of certain parameters is enabled on the AUTOMATIC logging screen.
The following additional functions are available only for Kenwood radio
control:
<PgUp> These keys may be used to control the radio VFO by slewing
<PgDn> frequency up when <Pg Up> is pressed, and down when <Pg Dwn>
is pressed. The tuning rate begins in 10 Hz increments, then
switches to 100 Hz, and finally switches to 1 Khz if the key is
held down. Once the key is released for a second, the rate resets
to the slow 10 Hz tuning step.
<F10> The <F10> function key causes the optional Rig-EQF radio control
program to "pop up". Rig-EQF provides advanced control features,
including local memories, programmable scanning, and a large
frequency display. Rig-EQF is available as shareware from N3EQF.
<Alt>-V is used to switch between VFO A and VFO B. The current VFO is
displayed to the right of the current frequency. The opposite
VFO frequency is also displayed, to the right of the current VFO
display.
TNC OPERATION PAGE 7.0
TNC OPERATION WITH Log-EQF
--------------------------
Log-EQF operates as a generic communications program, or "dumb terminal",
for use with any TNC capable of software control via an RS-232C interface.
Log-EQF communicates with your TNC through the COM port you specify from
the CONFIGURATION SETUP menu. The baud rate used for communication
between the TNC and your computer must also be entered on the
CONFIGURATION SETUP menu. If your TNC uses automatic baud rate control,
it should be disabled and set to a baud rate which matches the rate you
select from Log-EQF.
NOTE: Commands vary between models of TNC's, so no attempt to specify TNC
commands will be made in this document. Please consult the documentation
for your specific TNC to find the applicable commands.
Other communications parameters related to TNC operation are Parity, Data
Bits, and Stop Bits. Your TNC must be set to match the parameters you set
on the Log-EQF SETUP MENU. The defaults are No Parity [N] (this may also
be Even [E] or Odd [O] Parity), 8 Data Bits, and 1 Stop Bit.
The most common problem with communication between Log-EQF and TNC's
concerns the setting of the ECHO parameter. If you do not see any
characters displayed when you attempt to control the TNC, check to be sure
the TNC is setup to echo characters sent to it. (Try typing ECHO ON).
When you enable the TNC control by specifying a COM port and a baud rate
from the Log-EQF CONFIGURATION SETUP menu, TNC control is selected by use
of the following keys on the MANUAL and AUTOMATIC logging screens:
<F8> This key may be used to select the full-screen terminal emulation, or
TNC CONTROL screen. This is the screen you will use to TRANSMIT data
over the TNC, or to monitor received TNC data when not logging a
contact. Additional features for TNC control are also accessed from
this screen, including file transfer and dumping TNC output to your
printer.
<F9> This key presents the PacketCluster (tm) DX Spot screen. When you
monitor the PacketCluster, and DX announcements are received, the
previous 10 spots will be displayed on this screen. To work a station
displayed on the screen, move the highlight bar to the station you
wish to work, and hit <Enter>. Log-EQF will return you to the logging
screen, with the DX stations's callsign and the spot frequency
automatically entered into the log. If you have a radio interfaced
to your computer, the radio will also be placed on the correct
frequency.
TNC OPERATION PAGE 7.1
FILE TRANSFERS
--------------
When TNC communication is enabled, Log-EQF may be used to transmit
(upload) or receive (download) files. This operation is available only on
the full-screen TNC CONTROL screen, accessed from the logging screens. Two
keys on the TNC CONTROL screen are used to perform file transfers:
<F3> This key is used to RECEIVE, or download, the information being
received from the TNC into a disk file. Log-EQF will prompt you to
enter the name of a disk file. If the file you name already exists,
Log-EQF will ask you if you want to overwrite it or append to it.
Make sure you aren't about to eliminate a disk file you need before
electing to replace it!
To end the download, hit the <Esc> key. Log-EQF will continue to
store information into the file until you do this, or when you run
out of room on your disk!
<F4> This key is used to TRANSMIT, or upload, a file to a connected
station or BBS. If you are running PACKET, establish the connection
before initiating the upload. If the file to be transmitted contains
any non-displayable characters (such as in an executable program
file) you must also be in TRANSPARENT mode.
Log-EQF will prompt you for the name of the file to be sent when you
first hit <Page Up>. The transmission will begin as soon as the
program locates the disk file you specify.
You may hit the <Esc> key to end a file transmission, or wait for the
end of the file when Log-EQF will return to the normal TNC CONTROL
screen operation.
TNC OPERATION PAGE 7.2
MACRO KEYS
----------
The function keys <F5> through <F10> may be programmed for use as macro
keys. (A macro is a way to combine steps or text into a single file so
you don't have to type as much). You may setup the macro keys to execute
commands for your TNC, such as a single-key "HELP" function. Macro keys
may also be created to playback information such as contest CQ's or
exchanges, or with information like your name and QTH that you often
transmit over CW or RTTY.
Macro information is contained in disk files called 5.KEY through 10.KEY,
which you create using a text editor. Make sure the editor you use does
not insert any special characters for formatting. There are only a few
"rules" to follow in creating macro files:
1. Log-EQF will output a carriage return at the end of each line of text
in the file. This means if your macro file contains only the word
HELP, Log-EQF will output HELP followed by a carriage return
character.
2. If you want to output a "control character" (one which is formed by
holding down the <Ctrl> key) to your TNC, you may use the "^"
character in the macro file. For example, if you need to output a
<Ctrl-C> character to the TNC, you would type "^C" in the macro file.
3. A carriage return may be inserted into a macro file by using the
text: "<CR>".
4. An "escape" character may be inserted into a macro file using the
text: "<ESC>".
Some example macro files have been included with Log-EQF. The <F5> key is
setup to force certain parameters to "normal" conditions for use with Log-
EQF, such as ECHO ON and BKONDEL ON. You can expand this file to restore
proper TNC operation for your configuration. This can be useful when
switching between Log-EQF and other terminal programs which might set your
TNC to different parameters automatically.
NOTE: The <F11> and <F12> function keys can also be used on the TNC
screen. These "hot keys" cause a SHELL from the Log-EQF TNC screen
to the program or commands specified in two BATCH files, called
SHELL11.BAT and SHELL12.BAT. You can customize the two files to
suit your needs, using a text editor.
TNC OPERATION PAGE 7.3
PACKETCLUSTER
-------------
To use PacketCluster (tm) with Log-EQF, just connect to a node on the
cluster from the TNC CONTROL screen. When you return to either the MANUAL
or AUTOMATIC logging screens, Log-EQF will display PacketCluster activity
on the bottom 6 lines of the logging screen.
To make a PacketCluster DX announcement, hit <F9> from the logging screen.
You will be presented with the PacketCluster screen, which shows the last
15 DX spots received, and permits you to send a DX spot to other stations
on the cluster. Hit the <F1> function key to announce DX. If you have
already entered a callsign on the logging screen, it will be entered
automatically for the DX spot. If you are using a radio interface, the
current frequency will also be entered automatically. You need only enter
a comment, if desired, and hit the <Enter> key to send the DX
announcement. If either the callsign or frequency were not entered, you
must supply that information before hitting <Enter>.
Other PacketCluster transmissions, not in the DX spot format, must be made
from the TNC CONTROL screen.
If you do not intend to make any transmissions over the PacketCluster, you
do not need to connect to a cluster node. Log-EQF will still monitor DX
announcements from other stations, and post the last 10 spots on the
PACKETCLUSTER screen.
LIBRARIES PAGE 8.0
8. MAINTENANCE OF THE DX PREFIX AND STATE LIBRARIES
----------------------------------------------------
The DX Prefix Library is a disk file called PREFIX.LIB, which is
accessed by Log-EQF whenever the <F5> function key is depressed from
the Automatic or Manual LOG ENTRY screens. The file contains a list of
possible callsign prefixes, with corresponding DXCC prefixes, ITU zones,
CQ zones, ITU continents, and Latitude/Longitudes for each.
Since the DXCC country list changes fairly often, it will probably be
necessary to update the prefix file from time to time. It is extremely
important that the format of the library file is not changed if you edit
it, or the file cannot be read by Log-EQF. The information in the file
must be aligned in the proper column, or an error will occur when the
program tries to read entries from the library.
If you are a REGISTERED USER of Log-EQF, you can use the utility program
called DX-EQF to edit the PREFIX.LIB library file. Activate DX-EQF and
access the "<F5> LIBRARY" feature. You may then follow the prompts to add,
delete, or modify the entries in the library. DX-EQF will take care of all
the details (outlined below) to organize the library file. See Chapter 10
of this document for details on operating DX-EQF.
LIBRARIES PAGE 8.1
If you decide to edit the library file without the assistance of the
DX-EQF program, you must use an editor which does not add any control
characters to the text. The only non-printable character which may reside
in the library file is the carriage return, following each line of text.
The following rules apply to the file format:
1) Each line in the file must have exactly 80 columns in following format:
1-----6--------14-------------38------52------66------69------74-----80
^ ^ ^ ^ ^ ^ ^ ^
Prefix Country Name CQ Zone Latitude
DXCC ITU Zone Continent Longitude
The "ruler" above shows the column number where the file data must
begin. As long as you line up the information you add or change with
the rest of this file's information, you should have no problem.
2) Longer Prefixes must precede shorter ones which have the same
characters. For example, "ZL7" must occur ahead of "ZL", or else
ZL7ABC would be incorrectly reported as New Zealand, instead of
Chatham Island when the library is searched.
3) If more than one DXCC prefix exists for a single callsign prefix,
the DXCC prefix must be preceded by an asterisk ("*"). For example,
since both Bouvet and Peter Island are recognized by the "3Y" prefix,
the following two lines are present in the file:
3Y *3Y/B Bouvet 67 38 AF -54 3.4
3Y *3Y/P Peter Is. 72 12 AN -69 -90.6
4) Please note the sign conventions for Latitude and Longitude. Latitude
is positive if it is North, and Longitude is positive if it is East.
LIBRARIES PAGE 8.2
A second file called STATES.LIB is searched anytime you hit <F5> and you
have already entered something into the STATE log field. If a match is
found with the STATE you have entered, the BEAM HEADING display will be
updated for the corresponding location. Also, there is an optional field
in the STATES.LIB file, which can be used to display whatever you choose
whenever this STATE match occurs. You could, for instance, edit the
STATES.LIB file to include the ARRL SECTIONS for each state or province.
You may edit the STATES.LIB file to customize it, as long as you follow
these rules:
1) Each line in the file must have the following format:
STATE, Latitude, Longitude, Optional Comment
2) If you do not supply an "Optional Comment", the last character on each
line of the file must be a comma (",").
3) Latitudes and Longitudes follow the same format as for the DXPREFIX.LIB
file. Latitude is positive if it is North, and Longitude is positive
if it is East.
Always make a backup file before editing the library files, in case some-
thing goes wrong!
IN CASE OF TROUBLE PAGE 9.0
9. IN CASE OF TROUBLE
----------------------
Every effort has been made to provide a bug-free program, but as with any
software, there may be combinations of events which cause problems.
Below are some suggestions for locating the source of problems with
Log-EQF should they occur:
(1) PROBLEM: Log-EQF "hangs-up" the computer; no error messages are
displayed, and no way to recover use of the computer until it is
"re-booted".
- Check to see if there are any memory-resident ("TSR") programs
running at the same time as Log-EQF. One way to verify this is by
listing your AUTOEXEC.BAT and CONFIG.SYS files, to see if any programs
are being activated automatically when your computer is started. Some
programs can interfere with other program operation. If there are any
programs of this type on your machine, try removing them temporarily
and running Log-EQF by itself. It is also possible that the parameters
stored in file Log-EQF.CNF are not valid. Try deleting the file from
your disk and then run Log-EQF again. The program will create a new
configuration file with default values when you start it.
(2) PROBLEM: With a radio interface installed, a "RADIO I/O ERROR" message
is displayed while Log-EQF is running, and no radio control operations
function.
- If you are using a Kenwood radio, be sure the cable you are using
between the interface and the computer has at least 5 wires connected.
Besides the ground, transmit, and receive data signals, your cable
must include the RTS and CTS signals as well. Consult the users
guide for your radio and interface for more information.
(3) PROBLEM: The error message "COMMAND.COM not found" is displayed after
attempting to SHELL to DOS or another program.
- Log-EQF requires the DOS file COMMAND.COM to be installed in the
root directory of the same disk as this program. If Log-EQF is
installed on disk C: then COMMAND.COM must be installed in the "C:\"
directory. COMMAND.COM is the DOS file which contains all internal
commands. Consult your DOS manual for more information.
IN CASE OF TROUBLE PAGE 9.1
(4) PROBLEM: Log-EQF displays the Main Menu with a message "ERROR CODE xx"
at bottom of the screen.
- There are various routines which attempt to recover from most error
situations within Log-EQF. If you see the above message, with an
error number in place of "xx", then an error occurred which can
not be recovered. This can only happen if Log-EQF encountered a
situation for which the program does not provide recovery action.
- If you find you are getting errors under certain conditions, try
to isolate the problem by retracing your steps. If you cannot
resolve the problem in this manner, please write or call for technical
support using the information at the front of this manual.
(5) PROBLEM: A logbook data file cannot be loaded successfully by Log-EQF.
- There is always the possibility that your data file has been
corrupted, either accidently from an incorrect DOS command, or as a
result of a power glitch or some other interruption during a disk
save operation. Log-EQF creates a backup file regularly when you
perform an edit, sort, or search-with-output-to-the-disk operation.
The backup file's name is always "xxx.BAK", where xxx is your logbook
file name. To load from a backup file, just type the DOS command
"COPY xxx.BAK xxx.LOG", where again xxx is the logbook name, and
then start up Log-EQF. (You should create regular backups using the
BACKUP option on Log-EQF's LOAD LOGBOOK menu).
- A utility called FILE-EQF is available to registered users of
Log-EQF, which provides a routine which attempts to recover damaged
logbook files. FILE-EQF also can be used to convert between Log-EQF
files and other file formats, including dBASE, ASCII, CT, and NA.
(6) PROBLEM: When printing logbooks or QSL labels, "funny looking"
characters are printed instead of lines.
- Check the setting for <F2> PRINTER TYPE on the SETUP menu. If it is
setup for "GRAPHICS", hit <F2> again until "STANDARD" is displayed.
(7) PROBLEM: QSL Labels will not line up with proper spacing using a
laser printer.
- Check to be sure your laser printer is setup for 6 lines per inch,
or 60 lines of text on a 10-inch page. Other programs may send
control codes to your printer to control font size and spacing, so
you may have to manually set your printer. Top and left margins can
then be adjusted from Log-EQF to align the first label on the page.